Joined in 2023 
82 
63 About this deal
With any of the above, inspection reports can be produced if required using our FARO GAGE arm with Geomagic qualify probe software to show repaired areas against your supplied CAD, or against a measured or white light scanned by us equivalent mirrored area. What you’ll need to do is make the repair on the inside of the tube. This is a little bit different but still perfectly possible. Follow these steps: This includes: (1) identifying and rectifying the origin of any fracture or damage, (2) the surface must be thoroughly cleaned and degreased, (3) loose carbon fibre debris is removed, and (4) appropriate support is installed before the repair process begins. If the damage leads to a decrease in the load-carrying ability of the part, then users are presented with a choice: to repair or replace that part.
Using some of the abrasive paper (120 grit) ‘key-up’ the inside of the broken pole so that the surface is clean and scuffed ready for the repair to be applied. If you can't see any 'weave pattern' like small squares in the professional repair then it's likely they've used a unidirectional carbon fibre reinforcement, rather than a woven reinforcement. It would be possible for you to use this same reinforcement in your home repairs, in fact we do sell unidirectional reinforcement, although there would be some extra considerations if you use this format of reinforcement. Any product that you have subsequently cut, shaped, broken or modified, unless found to be faulty or defective. aff ordable : kits are significantly more affordable than hiring a professional to repair carbon fibre damage . High-energy impact at low speed = delamination in larger areas without visible damage to the exteriorTypical hand laminates, even when vacuum bagged, end up with a significant amount of excess resin. Excess resin increases the brittleness and reduces overall properties. On the other hand, most pre-pregs contain around 33% resin. This is the ideal resin to fibre ratio for optimal strength/ stiffness/ lightweight properties and generally impossible to achieve in normal wet/ hand lamination. Once cured, twist the good pole to remove it from inside the repaired pole. The pole should come out from inside the shrink tape. Next, remove the shrink tape from the inside surface of the repaired pole. ease of use : these kits come with all the materials needed to make repairs and refurbishments. There are also detailed guides and instructional videos available. Our Carbon Fibre Epoxy Repair Kits are a useful set of tools and materials to complete any carbon fibre repair. We have two variations of these kits. With bold coloured laminates such as carbon fibre, the underlying colour of the fabric may still show through the pigmented resin, especially with thinner layers of resin over the underlying laminate.
A carbon fibre repair kit can be a helpful tool for fixing damaged carbon fibre components. However, it is important to be familiar with the material and the repair process before attempting to fix anything.So you’ve got a broken carbon fibre fishing rod and now you want to repair it well this is the kit for you! Bring the two halves of the pole or rod together if necessary and secure them for the duration of the repair. There are several Carbon Fibre repair route options open to us depending on what is available and what you require: roll of Surface finishing tape. This is the exact tape we use in day to day repairs ourselves. It is not a ‘shrink tape’ as supplied with other kits. A surface finishing tape leaves a glossy, ‘lacquered’ look to the finished repair, reducing the need for extensive sanding and lacquering. When wound over the repair as directed, under slight tension, there is no need for a shrink tape as the tension applied will create the ‘shrink’ needed. Also, after researching the many ‘shrink tapes’ available, we found that a certain (normally very high) temperature is needed to activate the shrinkage and that temperature needs to be held constant for a certain time period. We felt this couldn’t be achieved at home with a hairdryer of heat gun.
x 150mm top quality carbon fibre cloth. 1k 90gsm (this means it is thin, lightweight, not bulky and obtrusive, yet strong and has a nice tightly woven pattern). NO GOODS manufactured or sold by Advanced Materials Technology Pty Ltd will be accepted for a credit if returned after one (1) calendar month of original invoice date. The kit includes all of the necessary materials and equipment to repair a carbon fibre fishing pole and requires only competent practical skills and a couple of hours of your time to repair your broken or fractured fishing pole or rod so that it is as strong as it was before the damage occurred. This is a performance, economical and overall feasibility decision. Carbon fibre parts are expensive, so a repair is often preferable if the original properties of that part can be matched in the repair.
PRODUCTS OFTEN PURCHASED WITH THIS ONE
If you need to push the HDT of the finished part higher then you could increase post-cure up to a maximum of 80°C as follows: Safety Precautions: Wear gloves and goggles and work in a well ventilated area. Always read the SDS before use.
Carbon Fibre Twill is pliable for shaping, making it great for repairs. It is most commonly used in auto and canoe repairs. Damage causes a slight reduction in load-carrying ability or a slight loss of carbon fibre laminate, then a replacement or repair may be more appropriate. Carbon fibre reinforcement with epoxy repair resin is a possible option.A simple and very effective post-cure cycle with the IN2 Infusion Resin (or EL2 Epoxy Laminating Resin) is as follows: Clean up any resin that has dribbled through to the outside of the repaired pole using abrasive paper. Channel Islands; Inflatable dinghy price on request Channel Islands; Flares not available to ship at this time
Great Deal 
New Comment