Triton 1100W Thicknesser 317mm TPT125 (583534)

Product Information

But it copes brilliantly when cutting full width planking, too. Maximum cut (I measured) width is 31.5cm. Electric motors don't like to be strained, so don't over work it, and it should last a lifetime. It certainly feels like it will last many years with only the removable blades needing resharpening occasionally. I did have a lot of difficulty in removing and inspecting the blades as the retaining screws were so tight that the tool that is supposed to open them got damaged at the tip. Finally had to get the dealer to help loosen the screws with better equipment. I have reassembled the blades and now can remove them easily for sharpening or replacement. It is a great machine and well worth the money paid for it. It looks and feels solid and strong. Glad I got this unit. So far the finished face of the timber has been flawless, I note that some revies say you have to waste the first and last couple of inches of timber timber due to "snipe" I have found that by adjusting the feed plate slightly, feeding the timber flat on the feed plate and on longer pieces have a support, ideally a Triton Multi Support Stand, the problem is eradicated. While we’re not ranking this category we do feel the data is interesting and informative. As you can see above the DEWALT DW735X pulls some serious amps under load. It points to the much more powerful motor in that unit. The power difference was clear during the planing operations as it didn’t seem to care what we ran through it. But it’s important to note if you’re going to buy the DEWALT DW735X you MUST have a dedicated 20A circuit as it’s not going to run well on a 15A circuit. We wanted to know how each machine performed at maximum loads (which results from cutting at the maximum depth in a single pass that the manufacturer recommends). More specifically, we wanted to know which planer pulled more power (maximum amp draw) and which one had the best feed performance relative to its no-load condition.

Most of the planers utilize a bolt to adjust the table vertically with a captured nut to hold the adjustment bolt in place. All of the units had a similar table adjustment but one. We were very impressed with the Makita planer and its setscrew adjustment. The Makita machine had, by far, the easiest adjustment method of all of the planers. The four setscrews were easy to reach and we found it easy to dial in the proper adjustments. I was looking to set up a micro woodworking shop as I have limited space and looked hard at what was available and came across Triton initially via Men in Sheds. I then looked at the story behind Triton and then where I could buy their product. I selected Yandles and it was a good decision. I am a more than capable DIYer as I spent my school and university holidays ladding for tradesmen.

Here are the spare parts for the Triton TPT125 planer!

Sporting a 1,250 Watt motor that spins the blades up to 8,000 rpm, this Scheppach planer is more suited to small pieces of wood. With a maximum cutting width of just 204 mm and a height of 120 mm, it’s not the best in its class, but it’s enough for most DIYers. If you have any volume of work to do, this will pay for itself RAPIDLY in terms of time and cost savings. Im very impressed with the quality of the machine as well as its performance, for the very reasonable price. What’s interesting about this data is how well the snipe length correlates to the distance of the rollers inside the planers from the cutting heads. The length of snipe on all the models we tested nearly mimic this distance. The nice thing here is the snipe should be predictable for each model and allow users to plan accordingly. Users of the DEWALT DW735X will ultimately “waste” more material over the life of the planer. However, with all the planers having relatively the same amount of snipe we’re not ranking this category either but rather letting you see how they all compared. Since I've received my new planer, I've had the opportunity to use it. It's a delight to use. I was pleasantly surprised that the noise level was lower than anticipated. The machine cuts very smooth and clean, only light sanding needed for a final finish. While I was hesitant to buy a machine that I couldn't find a review on, I'm onboard. Triton has a new customer and I've become very confident in not only their product, but their fantastic US customer support.

I'm giving 4 out 5 stars, just for the fact I had to return my old device and wait on a replacement. The replacement was at my house, in less than a week. While all the planers produced a “smooth” finish to the touch, there was quite a variation of smoothness resulting from the milling marks and scallops. The DEWALT DW735X was by far the best finish of all the samples we planed. The amplitude of the milling marks was consistently smaller and there was very little “scalloping” of the surface compared to all the other planers. This is likely attributed to the powerful motor and excellent blades. In addition, the 735 has three blades in the cutter head. Coming in 2nd place was the Triton TPT125 followed by the Ridgid R4331 in third place. Both the Triton and Ridgid had similar results. Coming in 4th was the Delta 22-590 with minimal milling marks but noticeably more scalloping. Blade Change Evaluation

For Triton TPT125 Planer outfeed roller

The sheer volume of shavings (I mention this just in passing) is like other planers - i.e. substantial. You'll have unlimited free pet bed shavings or material for the meat smoker, for life. (Just be sure not to use the kiln dried treated nor green-stained timbers in either case). We tested how much material would be ‘lost’ to snipe. We had already adjusted each planer’s tables to be flat, and level to the planer bed, prior to the snipe test. This machine has a maximum cutting width of 150 mm, and to help you deal with odd-shaped pieces of wood or even plastics, there’s a detachable fence on the side of the table. This can be angled anywhere between 90° and 135°, depending on the job at hand.

What it won't do is square up wood that was cut on an angle (or a deliberate mitre or slant) like a parallelogram. If the face you feed into the machine has a continuous and uniform angle cut into it, it will level the face but maintain the angle.

Planers can also tear out small chunks (scallops) from the surface. Between the milling marks and scallops the board could require more or less sanding to create a finished surface that will take paint, stain or clear finish well. We applied blue chalk to the surface to highlight the milling marks, and scallops, for a visual inspection. We also evaluated the smoothness by simply feeling the surfaces. While very subjective, we ranked the planers based on the samples of Maple shown below. The 31.5cm max width has a curved input around the entry edges. What this means is that if you insert a long plank slightly skew, the curved edges will slowly push the wood straight if the wood being planed is put in at an angle. Another nice touch, it self straightens your product. British tool brand Silverline have been around since 1978 and are well known for their budget-friendly kit. Their take on the best bench planer for woodworking is their 344944 planer. It’s a solid and simple machine that gets the job done if you don’t want to splash the cash too much.

The feeder entrance is very tightly and well matched to the cutting blade height. What can JUST squeeze in, will just get planed. You never remove too much surface material once you are accustomed to its behaviour and performance, the machine is predictable in that sense (in a good way) and consistent. We’re not going to rank this category as we feel a bench-top shop tool like this will always require some setup and fine tuning. Of the 8 planers Makita definitely has the best system for making those adjustments. You should also wear a dust mask, safety goggles and ear defenders when using your planer. Never wear loose clothing, such as ties, scarves or jewellery, when using the machine as these can get caught in the rollers. It is a heavy machine and requires a substantial stand, I built mine to meet my personal requirements. It is not a machine suited for continuous commercial use but then is not sold as such. All in all exellent value for the price. The no-load speed of 8,500 rpm and maximum planing depth of 2.8 mm per pass is impressive for a benchtop planer. It means you can get a lot of work done without needing to make too many passes. The 7.5 m per minute feed rate isn’t too bad either.

Depth of Cut Accuracy– For this evaluation we wanted to look at how accurately the planers remove a specified depth. Each planer has a dial that when turned a specified amount will theoretically remove a given depth in a single pass. We compared how accurately each planer was able to remove a fixed depth based on the dial. Anticipate a delivery window of 2-3 business days, although the objective remains within 48 hours post-dispatch. The machine itself about as noisy as a table saw when spinning by itself, but the cutting noise is perhaps less noisy, less shrill than a table saw when planing. The total noise volume is significant though, in the same league as a table saw at work. i.e. Noisy! Protect your ear drums and use ear defenders. Above you can see a graphic showing the ratio of the no-load feed rate compared to the average loaded feed rate (average feed rate for the materials we planed). This just gives a good relative comparison of how the motors performed under load. The DEWALT 735X and the Triton TPT125 were able to keep the feed rate much closer to the no-load rate compared to the rest of the field.