1 Pack of 5 Replacement Break Glass for Fire Alarm Call Points

Product Information

If you happen to uncover a fire at work, sounding the fire alarm using a manual call point is the fastest way to get your colleagues’ attention and prompt them to get to safety. If the fire isn’t big enough to have triggered the automatic fire detection system, your proactive actions could help put the flames under control before the fire has had the chance to spread. Ionization Smoke detectors work based on lowering the current flow through the inside chamber due to ionization which leads to initiate the alarm. As a general rule, you must have a call point within 30 metres of any location within a building and there should be at least one on each storey. High-risk areas may need additional call points installed.

BRE Global report finds compatibility between NFPA 72 code, EN54 standards". FMLink. 2010-06-04 . Retrieved 2023-02-05. Usually, the user will break the glass and press the emergency button centred in the middle of the unit. This will then activate a centralised alarm system to alert building wide that there is an emergency. When deciding where to place fire call points, it is essential to remember to put them near areas where risks are higher, such as kitchens. In a wireless fire alarm system, all the detectors and related devices are interconnected remotely through radio communication to the fire control panel. Manual fire alarm activation is the process of triggering a fire alarm through a call point, pull station, or other device. This usually causes the alarm to sound the evacuation signal for the relevant building or zone. Manual fire alarm activation requires human intervention, as distinct from automatic fire alarm activation such as that provided through the use of heat detectors and smoke detectors. It is, however, possible for call points/pull stations to be used in conjunction with automatic detection as part of the overall fire detection and alarm system. Systems in completed buildings tend to be wired in and include a control panel. Wireless activators are common during construction.The following tutorial will explain the different fire alarm system and their wiring diagrams and connection

High-use areas – to protect your calls points and fire alarms in areas that experience a high volume of traffic or use, you can use a Protective Cage. These cages will protect the call points from being accidentally activated or unintentionally damaged. Altering the environment – you might be tempted to put headphones in whilst the testing is being carried out, unfortunately, you shouldn’t do this. When you activate the manual call point, it sends a signal to the fire system’s control panel, notifying it that there is a fire in the area closest to the call point. As a minimum, this will sound the fire alarm throughout the building. It should also start the fire emergency protocols, including calling the fire brigade.Another interesting fact about manual call points is that they should always be installed on the floor side of an exit door leading to a staircase so that when the alarm is triggered, the alarm system can correctly identify which floor the fire has occurred on. The Safety Centre has an extensive range of fire and safety products that we supply to companies and individuals worldwide, with over 30 years experience you can trust us to deliver a bespoke solution for all your fire and safety requirements.

Depending on the model of the call point you may or may not have to break a glass to reach the button that activates the fire alarm. Some of the latest designs have been adapted to use depressable plastic instead of glass to reduce the possibility of injury to the user and to discourage any acts of vandalism. Each use of an emergency account should be reviewed. The use of an emergency account may be valid, or it might indicate a malicious act. Unacceptable use needs to be recorded and acted upon. Frequent use may indicate problems with the normal user authentication mechanism. This regular monitoring of pre–staged emergency accounts should also include exercising some of them to ensure that they do work, and that their use can be detected. This is similar to testing fire alarms, to be sure that they will work in a real emergency. Cleaning Up After Account Usage Note: Ensure that the individuals who create the accounts are not the ones reviewing the audit trails since this can be a source of abuse. In the wireless fire alarm system, a radio signal is transmitted from the detector (such as heat detector) or call point to the central fire alarm system to activate the alarm circuit.Alternatively, if you want to create an intelligent fire detection network in your building, you can use the XP95 Intelligent Manual Call Point, which is designed to work as part of a holistic fire detection system.