Salmue Cotton Bed Canopy+Steel Ring+Hooks +Hook Base Plates +Adhesive Tapes+Screws Block Out Light Dome Princess Mosquito Net Equip With Assembly Tools(Khaki)

Product Information

Some hinged wall-mounted rails can be supplied with a support leg which rests down on the floor when the rail is horizontal, transferring some of the load from the wall to the floor. Bottom half of Arena grab ring is attached to inside of surround and the top half is attached to the mechanism.

sitting down or standing up from the toilet, or standing to manage your clothes when using a toilet The Arena adjustable bed grab rail, handle, ring or bed lever (depending on what you call it) comeswith anti entrapment andwas designed by Laybrook especially for domesticelectric adjustable beds. The Arena grab ring is attached to the side of the surround so it stays static when you change position on your bed, this makes it easy to use when getting in and out of bed, helps you turn whilst laying in bed, supports you when getting up out of the bed whilst sitting on the edge of the bed. Withother grab rings, when the head section of your bed elevates to the upright position the grab ring moves with the bed and impedes you from getting in & out of the bed. The lower portion is usually set horizontally and acts as a forearm support. This enables the user's body weight to be distributed through his or her forearm which may be helpful for someone with painful hands or wrists. They are fixed to the wall or to the floor behind the toilet and can fold down to a horizontal position alongside the toilet.Straight rails are wall-fixed rails which run in one direction only. They can be fixed in a horizontal or a vertical position, or at an incline or angle. Fixing to UPVC plastic door frames should be avoided as the frames are unlikely to have the necessary internal materials in the required area to support a grab rail's fixings. Consider the advice about the different kinds of grab rails. Identify the best types of rail for your particular requirements. THE ONLY DOMESTIC ADJUSTABLE BED GRAB RING FOR ADJUSTABLE BEDS WITH-OUT A LARGE PLATE ON THE FLOOR. When using these rails you must consider the integrity and strength of the surface to which you are fixing them. For example, when fixed to wall tiles, the attachment of the tiles to the wall MUST be secure.

If you have underfloor heating, or if you have a sealed/waterproof floor, such as in a wetroom, you should avoid fixing rails into the floor. You must also consider where any services, such as water/drainage pipes and electricity cables run inside the walls or under the floor.Some have a support leg which rests down on the floor when the rail is horizontal. Some models provide a single horizontal rail which provides support at one height; others consist of a looped rail which provides two alternative gripping positions. Some of these rails have a built-in toilet roll holder. A vertical rail at least 500mm long can be fixed at the entrance to the shower compartment for use when stepping in and out of the cubicle. The rail should be mounted at a height that the user can comfortably reach whilst stood both from outside the cubicle and from in the cubicle. When stood in the bath - A rail (at least 500mm long) can be fixed vertically on the wall, 600mm from the tap end of the bath (dimension b in above diagram), with its lower end 200mm above the bath rim (COT 2006 p13, H M Government 2015, p58, diagram 26). This is most likely to be of use when stood in the bath (perhaps whilst showering) or when standing from a bathboard over the bath. Horizontal rails may help when pushing up from sitting and provide support when lowering, e.g. on to a toilet. Most people find it easier to push down on a rail rather than pull on one, so horizontal rails are more commonly used. Part of the rail can be fixed at an angle of 13° upwards towards the head end of the bath to provide an inclined support.

There are many types of grab rail. The main types are briefly introduced below, before going into greater detail about grab rails and their use in specific areas of the home. Bottom half of Arena grab ring is attached to inside of surround via a U grip and the top half is attached to the static part of the mechanism with a clamping action, just twist the knob and the threaded clamp secures the bed lever onto the bed. GRAB RING STANDARD FITS ALL DIVAN ADJUSTABLE BED WITH A SIDE PANEL DEPTH OF 8-16 INCHES (THIS IS THE SIDE PANEL OF THE BED THAT THE GRAB RING WILL FIT TO). A 600mm long horizontal rail 680mm from the floor beside, and extending in front, of the toilet pan for use when sitting down on the toilet. This rail can be horizontal or set at an angle of up to 15 degrees. Alternative suggested measurements are a minimum 500mm long rail, at a height of 600mm from the floor, with the rear fixing 400mm from the wall at the rear of the toilet. The Arena adjustable bed grab rail, handle, ring or bed lever (depending on what you call it) has not got a triping hazard like the parnell premier grab rail, it also comes with anti entrapment and was designed by Laybrook especially for domestic electric adjustable beds. The Arena grab ring is attached to the side of the surround so it stays static when you change position on your bed, this makes it easy to use when getting in and out of bed, helps you turn whilst laying in bed, supports you when getting up out of the bed whilst sitting on the edge. With other grab rings, when the head section of your bed elevates to the upright position the grab ring moves with the bed and impedes you from getting in & out of the bed.Toilet frames are designed to provide horizontal support for pushing up from a toilet, or for steadying the body when lowering onto a toilet. The frame, which stands over the top of the toilet, can either be free standing or fixed to the floor. Floor to ceiling railsare vertical rails which are attached to both the floor and the ceiling. They can be held at any point up the bar for general support and can be useful in the process of standing up/sitting down. Next consider your ability to grip onto a grab rail. Do you have reasonable hand strength? Do you ever have pain in your hands, wrists, elbows or shoulders which would prevent you from pulling up or pushing down on a grab rail? What is your overall balance and ability to stand like? Suction grab rails attach to a smooth surface by forming a strong suction grip at each end. Some manufacturers state that they are not weight-bearing and are only intended to assist with balance. Others do not clearly state this, but give a weight limit for safe use. You are advised to read any guidance and seek further clarification if needed before you use these rails. They are highlighted as portable for visits and holidays. The height will depend on your needs, often at the same height as an existing banister rail. This is usually between 900-1000mm above the pitch line of the stairs.

These provide a horizontal bar in their lowered position. They should be fitted at waist/elbow level and approximately a fist width away from your thigh when sat on the toilet.This should be a flat, unknotted piece of wood, which is screwed into the vertical joining pieces of the partitions. The grab rails can then be attached to the board. The College of Occupational Therapists recommends a 144mm x 19mm board/pattress with its external corners well rounded and the board itself fixed to the wall at least every 900mm (COT 2006).