Joined in 2023 
82 
63 About this deal
Multi-channel output; up to 200W total output power; the output of each channel can be controlled independently Index ....................................................................................................... When powering on the instrument after powering off it, make sure that the time interval between the two operations is greater than 5s. To Replace the Fuse Each model has a 3.5″ TFT display, multi-colour on ‘DP8xxA’ models and selectable single colour on ‘DP8xx’ models.
Users can set the remote interface parameters, system parameters and print parameters. Besides, users can also calibrate the instrument, view system information, define the recall configuration of Preset and install options. The DG832 is a 35MHz, 2CH Function Generator with a maximum sampling rate of 125MSa/s. The Rigol DG800 series offers a user-friendly and high-performance function/arbitrary waveform generator solution at a very attractive price. Each instrument provides many functions including; function generator, arbitrary waveform generator, noise source, pulse generator, harmonics generator, analogue / digital modulator and frequency counter. Any Rigol DG800 series function/arbitrary waveform generator would be a valuable asset in any home, business or education laboratory. there are even more ways to use the supplies. New digital triggering between instruments also makes it possible to reliably combine and connect supplies together. Intuitive to use for everything from education labs to the R&D bench, the DP800 family of power supplies provide incredible value for any application. Make sure that the AC power to be connected to the instrument fulfills the requirements in Table 1-2. The following features are standard on ‘DP8xxA’ models and optional on ‘DP8xx’ models: High resolution output control, online monitoring and analysis functions, 4-off trigger inputs/outputs, RS232 & LAN interfaces.
Documentation
Update 1: TooOldForThis posted a Calibration Guide allowing manual calibration with SCPI commands that can be used successfully (and especially to recover from a previously failed calibration). Furthermore, ted572 posted a Calibration Procedure as a summary of the steps described in TooOldForThis's guide. The Firmware Installation Instructions are attached below: Although there is a serious flaw in the form of missing information. I'm sorry if this has been asked before and I'm not sure if this is the proper sub-forum to ask in.If it's not, I apologize and maybe a moderator could move the post.I have a Rigol 832 Programmable Power Supply.It's been absolutely wonderful.I found the keygen a long time ago to upgrade the unit.One of the upgrade no longer works.I can't remember which one but I remember reading that if I upgraded the firmware, the one option would be removed.I wanted to know if that ever got fixed?I can try and find out what option it was that disabled by the firmware upgrade if needed.I can't seem to find the forum anymore with the keygen. I thought it was here on EEVBlog.
Only the power cord designed for the instrument and authorized for use within the local country could be used.Note: Connect the positive terminal of the test lead with the (+) terminal of the channel output and connect the negative terminal of the test lead with the (-) terminal of the channel output.
Stellen Sie sicher, daß keinerlei Überspannung (wie z.B. durch Gewitter verursacht) das Gerät erreichen kann. Andernfallsbestehtfür den Anwender die GefahreinesStromschlages. RIGOL shall not be liable for either incidental or consequential losses in connection with the furnishing, use or performance of this manual as well as any information contained. Provide waveform display function to provide real-time and dynamic display of the output voltage/current waveform, clearly showing the output state and tendency of the instrument in together with the digital display of the voltage, current and power values Issue documented here. Rigol investigated and responded with the attachment "DP832 Recommended Connections.pdf". In brief, Rigol recommend a heavy-duty low-resistance wire between the GND terminals of channel 2 and 3 to reduce the measurement error. Provide overvoltage/overcurrent protection function; users can set the overvoltage and overcurrent parameters to realize effective protection of the loadIf you suspect damage occurs to the instrument, have it inspected by RIGOL authorized personnel before further operations. Any maintenance, adjustment or replacement especially to circuits or accessories must be performed by RIGOL authorized personnel. For the multi-channel model, the function of this part is channel selection and output switch. For the single-channel model, the function of this part is range selection and output switch. Turn ON DP800, Press Help when RIGOL icon comes up up. Install USB Flash Drive with the .GEL upgrade file when prompted.
Important Notes 1. If a firmware update includes a new bootloader, most likely it will prevent downgrading to a previous firmware released based on an earlier bootloader. For example, it is not possible to downgrade from 01.09 to 01.06. See here. Also, it was reported here that it is not possible to downgrade from 01.11 to 01.10 (which use the same bootloader).Restore all the settings of the instrument to default values or recall the user-defined channel voltage/current configuration. The menu item can be denoted by the format of "Menu Word (Bold) + Character Shading". For example, System denotes the "System" item under Less than 50μs for output voltage to recover to within 15mV following a change in output current from full load to half load or vice versa. After DP800 installs the file, and the DP800 automatically reboots. Remove the USB Flash Drive with the .GEL file. The hardware, for me, is the hardest part.I just started learning how to make circuit boards and don't have much experience in that area at all!I made a device that counts in binary (up and down) when you press a button!It lights up LEDs to show the binary number.I've written code most of my life and I've played with assembly on and off.After the Marine Corps, something happened to my brain and things got a bit messed up.Had to take a break for a bit but I'm ready to learn everything I can now.
Great Deal 
New Comment