Joined in 2023 
82 
63 About this deal
Concrete posts ensure you have a good strong fence, but they do need a fair bit of work to put up and they are quite heavy.
The concrete should be just above ground level. Trowel the surface smooth, sloping the concrete away from the post to let the water run off Similar butt joint reinforcement connections may be made using two to four biscuits inset into matching grooves cut into the ends of the 4x4s. Alternatively, cut a matching groove in the butt ends and glue in a wooden spline. Dowels, biscuits, and splines all reinforce the alignment and provide some lateral reinforcement. There are several ways to remove the wood to do the lap; however, the lengths and location do play a part. A basic hand saw, hammer, and chisel, or all three have worked for centuries. Electric or battery-powered skill saws or reciprocating saws are a modern convenience that may make the task easier. I’ve seen a good hand sawer do up a set of half-laps in the same amount of time as a reciprocating saw, and with much more accuracy.
Our choice for the strongest and easiest way to join two 4×4 posts is a half-lap joint that is glued, plated, and bolted. Cutting a half lap into an existing fixed post is easier than all other cuts, except the butt joint. The two required cuts per post are simple and doable even with limited space. Separate the joint, apply the compound evenly, and then reseat the two pieces using several through bolts to hold the alignment. As the bolts are tightened, the viscosity of the glue makes the pieces want to slide out of alignment, making clamping difficult.
Your fence panels may need to be trimmed to reach the exact length of fence you require. You will need to first detach the framing batten from one end of the panel. Then you can trim the panel using a saw and reattach the batten.Use string between the stakes to show the outline of your wall footing then use a shovel to excavate the area. To make a half-lap joint, measure to find the centerline of the two pieces and mark both sides at the end and near where the cut will end to form the seat. Measure from the end and mark the desired length of the cut and mark it on both sides and pieces. While the depth is always half, the length of the cut will depend on use and compliance with local building codes. Stepping involves constructing the fence so it has multiple steps down to match your sloped garden. Wooden posts are easier to handle. But as they’re buried in the ground, there’s a slightly higher risk that they’ll rot. However, if you choose decent timber that has been pressure treated then the risk of rot is low.
It may be a good idea to paint or seal your boards before installation, but this can also be done after. Vinyl fences are designed to go the distance. They are easy to maintain and won’t fade or degrade over time. They also don’t need to be sealed or painted. Most vinyl fences will come either as panels or boards and rails, and both types are designed to slot together. Measure and mark out where your fence will sit then follow steps three to four of our ‘how to build a fence’ section to install the posts. Chain link fences are another affordable option for marking property boundaries and preventing animals or children from escaping from your garden. Depending on your level of DIY experience and skill, figuring out how to build a chain fence will usually take you one to two days.
We Recommend
Wire connectors: These are used to connect two electric fence wires together, either at the end of a line or where two lines intersect. Two other reasons rest on transportation and availability issues. Carrying and connecting two 8-foot lengths is easier than transporting a 16-foot length, especially if traversing woodland trails. The availability of long 4x4s at many small suppliers is often limited due to low demand, making splicing a necessity. Repair Follow steps one to four in our ‘how to build a fence’ section to install your fence posts. Ensure you install posts in each corner of your fence as well as brace posts (to keep your corner posts stable) about eight feet from each corner. A glued, plated and bolted nibbed tapered scarf joint is stronger than a half lap but not as easy to cut in limited space. Although it too has two cuts per 4×4, accurate sawing is more difficult. The skill level and aesthetics of the finished joint influence the choice of connection. A poorly sawn joint won’t make for a strong connection. Conclusion
Using a pen or pencil, make six small marks along both sides of the batten framing. Ensure these are at an equal distance from each other. Traditional, natural, and beautiful, wooden fencing is extremely popular throughout the country. Wood is also a great material to work with and can be affordable. So instead of buying pre-built fence panels, why not learn how to build a wooden fence yourself? There are many reasons to join 2 4x4s together. Making a post longer, cut too short, repairing a post, building a longer piece for a skid, and post-to-beam connections are the most common reasons. Extend Posts Lengths of 3/8” to 1-1/4” dowels can be used to add lateral strength to butt joints. Carefully measure to bore and align 1 to 4 holes in the ends of each 4×4 and drill the holes between 1” and 3” deep. Cut the dowels to lengths of 2” to 6”, sand the cuts, glue, and tap into place.We would recommend installing gravel boards when building a sloped fence. This will prevent unsightly gaps at the bottom of the panels. Strip the ends of the wires to be connected or attached, so that about 1 inch of bare wire is exposed. Insert the exposed end of the tape into the connector, making sure the tape is securely held in place. A tapered scarf or scarph joint is a diagonal joint cut on a 1:8 to 1:12 slope and is as old as the half lap joint. It is commonly found in beams, skids or other horizontal members joined together with wooden pegs or bolts and plates. The scarf joint requires some modifications when used to extend a post.
Great Deal 
New Comment