Bosch F016800345 Replacement 8 m x 1.6 mm Spool Line for ART 35 Heavy Duty Trimmer

Product Information

which is further accompanied by abundantly growing greens, and not the formation of dead wood as a result of the work of the grass trimmer. How to remove the spool and replace the line Usually, the process of changing the line on a particular model trimmer is popularly described in the accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products. All these attachments do not allow you to change the length of the line in a semi-automatic mode (after pressing a button). If the cord breaks, you have to stop the mower and change it manually. DIY grass trimmer coil repair Trimmer mowing heads come in a variety of designs, both simple and complex. The picture below shows an exploded view of a semi-automatic trimmer head from a Husqvarna (Husqvarna) brushcutter.

Knowing how to disassemble the drum, you should continue to figure out how to change the grass trimmer line. The video below shows the detailed process of how to open the grass trimmer coil and disassemble it. Installing a new line on the grass trimmer reel There are times when the user of the grass trimmer notices a very fast line flow. At the same time, he never hit the ground with a button to lengthen the line. The reason that the line spontaneously lengthens, being cut on a special knife on the casing of the device, may be the absence of a spring in the mowing head. Often novice users of mowers, trying to load the line into the reel, forget to install the pressure spring in the head, or completely lose it when opening the lid, and in the future, do not even know about its existence. Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand. Drill a hole in the center of the disc that matches the diameter of the gearbox shaft. Do not forget to put a washer on it before installing the disc on the shaft. Switch off the brushcutter engine or power off the electric grass trimmer before threading the line into the spool to avoid injury from accidental starting rotation of the cutting tool.

Specifications

The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit Initially, remove the line from the spool of the grass trimmer before threading it into the spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it. This homemade mowing head is secured to the shaft with a nut. It will not work to tighten or unscrew the nut without fixing the shaft. To replace the cord, it will be enough to loosen the screws, insert a piece of line of the required length and press it again.

Assemble the mowing head. Be sure to insert the spring and washer (if equipped) before final assembly of the accessory. Place the spool in the body and thread the ends of the cord through the holes or lugs. This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances: Periodic removal of the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this. Slowly completed disassembly of the spool-spool without losing its spare parts allows you to move on to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions. How to remove the spool from the grass trimmer and remove the lineAfter that, you can proceed to dismantling. To do this, you do not need to pull it with all your strength, but slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated. If the line does not lengthen when you lightly hit the grass trimmer button on the ground, the reasons may be as follows:. Option 1. a bite has occurred, i.e. clamping the cord between turns. This problem usually appears if the user has been winding the line on the reel unevenly, with intersecting turns, or winding it with insufficient tension. In the latter case, when the mowing head rotates at high speeds under the influence of centrifugal force, the cord begins to tighten, as a result of which inter-turn clamping of the fishing line is possible. To fix the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, in even turns with good tension. In the first case, third-party cord can be made of low-quality and low-melting materials that cannot withstand mechanical and thermal stress. Therefore, you should give preference to “branded” lines.