Bestway Pool Drain Pump

Product Information

The clean-out port is an easily accessible part of the sanitary drainage pipes. You should open that and place the other end of the hose there. First, you’ll need to take off the drain connector from both the garden hose and the pool and put the hose directly into the pool itself. Regardless of how careful you are when maintaining your pool’s chemicals, sometimes your water is just beyond saving and needs replacement. During the busy summer season, it’s best to brush your pool with a nylon brush quite regularly. This will help get any algae out of corners and into the water filtration system. Make sure the brush is made of nylon so that it doesn’t scratch or tear your pool liner.

Once the filter panel closes, disconnect the circulation/filter hoses and ensure you mark their spots accordingly with tape or any other means before removing just as a reference spot while cleaning. To be prudent, wrap these hoses with plastic bags or cloths after draining to ensure foreign materials and debris are not clogged into them when stored away! Close the Drain Valve The label is often placed in a strategic position, and it’s easily seen from outside the pool area or along the interior surface, perhaps near the vinyl lining. All you need to do is read it carefully, follow its instruction and voila! You will locate the drainage valve stress-free. Connect a Garden Hose to the Drain Valve Whether you’re taking down your above-ground pool for the season or simply need to drain it for a cleaning, knowing how to properly drain your Bestway pool is essential. If done incorrectly, you could damage the pool and its components. Once you stop covering the end of your hose with your hand, the water should start flowing through.Once the hose is attached securely, you can begin to empty the pool by directing the flow of water away from your property. It’s worth noting that this may take several hours depending on the size of your pool, so make sure that you’re prepared for a longer drain time if necessary. The pump will no longer be useful once the water levels get too low. You’ll have to rely on the shop vacuum to get rid of the remaining water. How Often Should You Drain Your Bestway or Intex Pool If you look closely at your pool’s drain valve, you’ll find it has a cap on it from both sides. Use the drain connector between your garden hose and the drain valve and push it hard inside the valve so the cap inside the pool opens up and water starts to flow. Make sure to tighten the connector so that water won’t leak out of it. The next step is to locate the drain valve of your pool if it has one, usually located at the lower end or bottom, and close it to begin draining. Some Bestway pools come with a pool cover that aids drainage, remove this before proceeding.

Be careful if you’re going to drain your Bestway or Intex pool on your property, as the water may damage your lawn or garden. We use various chemicals like chlorine to keep our poor water clean. But unfortunately, in long-term usage, these chemicals lead to the formation of cyanuric acid. Although not always reliable, depending on how exposed the Bestway pool exterior is, you may see the drain valve physically without looking inside the instruction book. It’s important to properly maintain your pool throughout its lifetime. Properly draining your Bestway pool ensures clean and clear water for hours of summer fun” -Bestway Pools Monitor the Water Level So, how to drain above ground pool? Use a hose. It’s as simple as that. If the hose method is too slow for you, you may consider using a sump pump….and a hose!

You might consider

To keep your pool in tip-top condition, you’ll need to maintain a simple cleaning routine. A cleaning schedule with the right tools will help remove leaves or sand that could clog your filtration system or throw off your water chemicals. Filling your pool with water again may seem counterintuitive, but it’s only for a few seconds to ensure both ends of the hose are filled with water. Remember that draining the above-ground pool with a hose is a slow process that can take up to days for larger pools. If you’re unsure where the drain valve on your Bestway pool is located, the user manual can be a great resource. The manual will provide detailed information about all the components of your pool, including the drainage system and its location.

Keep in mind that this end of the hose should be on a lower level than the water of your above-ground pool. If you don’t do that, there will be no water flow. The first step you need to do is fill the hose with water. To do that, simply submerge the hose in the water. Then, hold both ends and direct them upward until the bubbles stop entirely.

All of this adds up to a pool that’s hard to treat with chemicals. So, unless you take down your pool every winter, you’ll only have to drain it every couple of years. Powered by a 220-240v motor, the Flowclear Pump ensures optimal performance and efficiency. With a remarkable flow rate of 3,028L (800 gal) per hour, it swiftly drains the water, emptying your pool or spa in minutes, ready to be refilled with crystal-clear water. One of the standout features of the Flowclear Pump is its extra-long drain hose, measuring an impressive 5 meters. This length provides incredible flexibility, allowing you to drain your pool or spa effortlessly, regardless of its location or proximity to a drainage area. No more struggling with short hoses or inconvenient positioning. The Flowclear Pump is engineered to make draining a hassle-free process. To further enhance its usability, the Flowclear Pump comes equipped with adaptors to connect to a garden hose. This feature opens up a world of possibilities, giving you the freedom to choose your drainage destination. Place your pump in the above-ground pool without connecting it to any electricity. Once the pump is stable on the pool’s floor and your hands are dry, connect the sump pump to an electrical outlet. Remember not to let the hose just drain onto the ground as that can damage any plants nearby due to fertilizer and chlorine in it.

Whether you prefer directing the water to a specific area or utilizing an existing drainage system, this pump ensures effortless connectivity and efficient water flow. Operating the Flowclear Pump is as easy as it gets. The power cord simply plugs into a standard electrical outlet, eliminating the need for complicated installations or professional assistance. Just connect the hoses, select the appropriate setting, and let the Flowclear Pump do the rest. It's a user-friendly solution that saves you time and effort, so you can focus on enjoying your pool or spa. Turn on the pump and periodically monitor the water levels as they reduce. This process will take around eight hours to finish. You’ll have to rely on simple physics to create a siphon in your pool. Follow these steps to know how:You may need to drain your pool and refill it with fresh water due to several reasons. Maybe you’ve exhausted the treatment chemicals in the pool, there are bugs in the water or layers of dead skin, or any number of other issues.