Sika Aquaseal Waterproof Tanking Membrane, Blue, 5 Litre

Product Information

Apply by brush in two coats which should be applied in different directions at right angles to each other to ensure full surface coverage is achieved with no weak spots. As the video shows, we first made sure that the floor and walls did not have anything loose on them and swept the areas to be covered thoroughly.

Pay careful attention to edges and corners to ensure that the coverage in these areas is always consistent as these are the potential weak spots where leakage could occur. Aquaseal Waterproof Tanking Membrane (5LTR) - Forms a permanently flexible watertight membrane, applied by brush, two coats. litre of liquid tanking primer (Styrene Acrylic based polymer) with a drying time of 1 – 2 hours depending on temperature of bathroom or wet room. For very porous surfaces, such as plasterboard, two coats will be required Aquaseal Waterproof Tanking Membrane 5LTR Forms a permanently flexible watertight membrane, applied by brush, two coats. Our tile adhesives collection will also assist in wet room construction. There’s ready-mixed tile adhesive as well as a practical adhesive and grout mixture.

How to Use the Aquaseal Wet Room and Tanking System From Everbuild

Aquaseal Waterproof Tanking Primer (1L) - For use before applying Tanking Membrane and Tanking Tape. Apply the first coat horizontally and allow to dry for 6 -12 hours then apply the second coat vertically. Our ready-mixed tile adhesives are a convenient choice, with general-purpose, water-resistant and grout options available. For a strongbonding porcelain tile adhesive, our powder range is up to the challenge. This range also features a white wall and floor tile adhesive for neat and tidy results. The membrane itself, despite being very thin (which allows it to flow onto the wall easily) is incredibly flexible as you would expect from any tanking system put into a high humidity area. Aquaseal Waterproof Tanking Tape (10MTR) - Self adhesive joint and corner sealing tape. Easy to apply with pre-cut release liner.

Aquaseal Waterproof Tanking Tape 10MTR Self adhesive joint corner sealing tape. Easy to apply with pre-cut release liner. The flexible drain mat was then applied around the floor drain. This mat can also be applied around any inlet and outlet pipes in the walls and floors and allows for any expansion and contraction in the hot and cold water as it flows through the pipes of down the drains. Then the vertical joints in the wall were sealed and all tape was pressed down thoroughly with the roller that is supplied with the wet room kit.For bonding and sealing joints, look no further than our tile grouts for protection against discolouration, water and mould. We always recommend the use of Tanking Tape on corners and board joints prior to applying the membrane to ensure the integrity of the watertight seal.

The Tanking Drain Mat is also recommended around the drain outlet and to reinforce floors and floor joints which is the area most susceptible to leaks. Aquaseal Tanking Tape provides cross directional movement at corners and on board joints and is available in 10 Metre rolls. Then we applied the Aquaseal primer with a 3 inch brush to the floor and the walls. This could be done with a bigger brush or even a fleece roller. Also, at this point it is worth noting that Everbuild’s Aquaseal Tanking Systems, both standard (4.5 square metres) and large (7.5 square metres) come with a paint brush and a roller. Our only criticism of the entire kit is that 2 brushes may well have been better. We’re the nation’s leading trade supplier with over 25 years’ experience. Whether you’re looking for internal or external tile adhesive, or even wood or tile on tile solutions, we’ll have a product that does the job.Everbuild Aqualseal Wet Room Tanking System Kit for 4.5sq Metres What is in the Standard Size Aquaseal Wet Room and Tanking Kit From Everbuild? Then we applied the second coat of the membrane making sure we finished off with horizontal strokes with the 3 inch brush which is supplied with the kit. Based on tried and tested wet room tanking principles used in areas such as Scandinavia and Germany where wet rooms have been common for many years.

Tanking membrane suitable for 4.5 square metres of wall and floor. This is a liquid waterproofing compound that is applied in two coats. The second coat can be applied 6 – 12 hours after the first then after 24 hours the tiling can commence A ready to use primer, applied by brush to all porous and semi porous surfaces in the areas that are toUse in showers, wet rooms, wet zones in bathrooms and other tiled areas subject to water exposure such as balconies and partially covered external areas. The Aquaseal Wet Room System is designed to provide a permanently flexible watertight membrane prior to tiling.