Audio-Technica AT-LPW50PB Manual Belt Drive Turntable - Piano Black

Product Information

The platter is a lightweight cast aluminum construction with a fixed radius for the flat belt and rib-like bracing towards the center to prevent platter resonance. The flat belt is already stretched and can be grabbed with a red ribbon from the top through the side hole. You put the platter on the platter bearing and pull the belt carefully over the pulley – done. priate force and resolution such that we could follow subtle instrumental strands even during the most climactic moments. The stereo image delivered was so precise it was easy to identify the position of instruments anywhere across the soundstage. Conclusion Currently at the top of that list is the AT-LPW50PB, available in Australia after some anticipation, given that it launched in the USA at virtual CES 2020.

The AT-LPW50PB is equipped with a built-in selectable phono preamp and a detachable dual RCA output cable to enable direct connection to components with or without a dedicated phono input. FEATURES Audio Technica AT-LPW50PB has built-in RIAA, but may always be bypassed if using external RIAA or RIAA integrated in amplifier. The AT-LPW50BT-RW turntable made the album sound even better when it had a wired connection to a component system. I tested it with both the built-in phono preamp and through my own NAD phono stage. The dedicated NAD unit sounded better with slightly more detail, but not by as much of a margin as I expected. Should you buy the Audio-Technica AT-LPW50BT-RW turntable?The light blue dashed vertical line at the centre shows the mean actual speed, which you can see is very slightly lower than 33.33 rpm at 33.324 rpm, so 0.006 rpm slow. Not significant. The purple and red dashed vertical lines show the wow measured according to DIN IEC 386 using both the dynamic method (purple dashes) and the 2 sigma method (red dashes). In terms of percentages, the measured wow using the DIN IEC 386 2 sigma method was 0.08% at 33.33 rpm and 0.07% at 45 rpm.

There is more information to be had too. Switching the phono stage off and moving to the iFi Zen Phono (to say nothing of the Cyrus), drops the noise floor further and reveals more information and better tonal realism at the same time. Judged by the competition, the internal phono stage that Audio Technica has fitted to the LP5X is perfectly satisfactory but - like the competition - there’s more to be had out of it. These two gold-plated RCA outputs have a diameter that is very slightly smaller than standard, so using standard RCA plugs results in a rather ‘loose’ fit and a tenuous electrical connection. You can fix this by squeezing in the outer (negative) ring of the plugs on the cable before you use them. Related: Best turntables Audio-Technica AT-LPW50PB build & features – Connections give it flexibility for hooking up other sources Hear all the detail that’s been missing from your records, with the beautifully engineered Audio Technica AT-LPW50PB.

Why is Audio-Technica AT-LPW50PB better than Audio-Technica AT-LP5X?

With a phono pre-amp built-in, the AT-LPW50PB connects to almost any hi-fi or speaker system. The phono pre-amp boosts the signal to line level, meaning you can connect it to any device with an AUX input. If you’d rather use your amp’s phono pre-amp, then simply switch off the turntable’s one. Likewise, a built-in phono-line preamp lets you connect up to a home stereo or powered speakers (that wouldn’t have a phono stage of their own) as soon as you plug the turntable in, letting you get to your tunes straight away. Playing Mary J. Blige’s No More Drama also saw this turntable turning in a cohesive and musical performance, with a surefooted and robust presentation that remained unflustered even as the song became more demanding, delivering plenty of fine detail and rendering the music with a lovely composure, though this was perhaps partly because it was just a little toned-down in the extreme highs. years as a part of the ‘95’ series. As with all the new AT-VM95 Series, it features the same dual-magnet design which, according to audio-technica “duplicates the ‘V’-shaped arrangement of the magnets in the cutter-head [of the recording lathe] and precisely positions the magnets to match the positions of the left and right channels in the groove walls” Prices valid in stores (all including VAT) until close of business on 28th November 2023. (Some of these web prices are cheaper than in-store, so please mention that you've seen these offers online.)