Brasso Metal Polish Wadding, 75g

Product Information

Don’t leave a job half done – Once you start using Brasso to clean a surface, you should finish cleaning the surface in one go. If you leave the surface to dry, you’ll have Brasso residue. And as a consequence of this, items might not look shiny and evenly cleaned. Below you’ll find steps on how to use Brasso in both liquid and wadding form. Skip to the section that applies to the Brasso you’ve bought. General tips to think about before you start using Brasso: Brasso, if used correctly, will naturally be worked into a surface, and any residue will be buffed away by a clean cloth at the end of the exercise. Note: You’ll likely have to use more Brasso for tougher, dirtier spots! And if your Brasso cleaning cloth goes dry, add more liquid Brasso to it or use a new piece of wadding. Benefits of using Brasso Brasso, on account of its ammonia content, has been used as a de-coppering agent in rifle barrels to remove copper fouling.

If you wish to return this item to Robert Dyas, you can only do so by the following method: 1. Visit Your Local Robert Dyas Store For use on brass, copper, stainless steel and chrome, this product has been specially designed to provide excellent results and a longer lasting shine. You should remove Brasso from small nooks before it dries– Use a small, slim tool that’s wrapped in a cloth to tease the excess Brasso from crevices. Leaving the Brasso to dry will just make it harder to remove, and you might not end up with the sleek finish you were after if there’s Brasso residue all over the place.At Stapleswe provide as many products as possible to keep you healthy and clean at work. Such as our Bathroom Dispensersrange where we offer products from Soap Dispensersto Paper Towel Dispensers. Key Information: Brasso is a well-known metal polisher, that can be used to polish, remove tarnish and clean up chrome, stainless steel, copper, and of course, brass. The label of Australian Brasso lists "Liquid Hydrocarbons 630g/L; Ammonia 5g/L", whereas the material safety data sheet for Brasso in North America lists: isopropyl alcohol 3–5%, ammonia 5–10%, silica powder 15–20% and oxalic acid 0–3% as the ingredients. [4] However, the Australian version contains kaolin instead of silica for abrasives. [5] When you’re done using your Brasso you need to store it away in a safe place, that is out of the reach of children and pets. This is not intended to be a full statement of your rights under the Consumer Contracts Regulations. Full details of your rights are available from your Local Authority’s Trading Standards Office. How To Return A Product

Keep an eye out for a blue and white striped pot that has a big red label on the front, with the name ‘Brasso’ on it.Technically speaking, as you continuously massage Brasso into the surface you’re polishing, you will be wiping some of the product off as you go. This is what’s supposed to happen. These wadding pads have been impregnated with cleaning fluid meaning there is no need to get an extra cloth dirty. Using Brasso to clean and polish grotty metal surfaces is super easy, and doesn’t cost you a fortune!

In addition to this, if you’ve used an appropriate amount of Brasso, and you’ve worked it into a surface and then buffed the surface again, you shouldn’t really have any excess Brasso left behind. So, you won’t need to ‘wipe Brasso off a surface’ per se. Brasso has been successfully used to take minor (white) heat marks out of French polished wooden surfaces. The fine abrasive cuts through the surface and allows the solvent into the wax and lacquer layer. The surface should be properly cleaned and waxed after this treatment. If you buy a liquid can of Brasso, you need to pour a small amount of the can’s contents onto a clean cloth to use the solution.Tip: If you’re using liquid Brasso, always pour the liquid from the can onto a clean cloth. Do not hold a cloth over the mouth of the can because this transfers dirt into the can. This then contaminates and weakens the Brasso inside the can. How to clean with wadding Brasso:

Anything of a nature that for hygiene or associated health and safety - this includes the Outdoor Spas, Mattresses and Divan Sets The online data sheet for Brasso wadding in the UK lists the ingredients as C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, C14–18 and C16–18 unsaturated Fatty acids, Kaolinite, Aqua, Ammonium Hydroxide and Iron Hydroxide. Brasso liquid lists a slightly different mix; C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Kaolin, C12–20 Saturated and Unsaturated Monobasic Fatty Acids, Aqua and Ammonium Hydroxide. Also available are ingredients in a discontinued recipe for Brasso. Wadding: C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Ammonium Tallate and Colorant. Liquid: C8–10 Alkane/Cycloalkane/Aromatic Hydrocarbons, Quartz, Kaolin and Ammonium Tallate. [6]Church, Roy A.; Andrew Godley (2003). The Emergence of Modern Marketing. Routledge. p.30. ISBN 0-7146-5390-X. Although, if you’ve used an appropriate amount of Brasso for the surface you need to clean, and you’ve worked the Brasso into the item and buffed it as well, there shouldn’t be any need to remove the Brasso with water. Perform a small patch test to make sure the Brasso doesn’t mark or stain the surface you’re about to polish. Brasso can be bought from most hardware stores and supermarkets. You’ll typically find it near to, or in, the cleaning products aisle.