Aquacomputer High Flow 2 53292 Flow Sensor G1/4 Aqua Water Cooling

Product Information

This Curve Controller right here alone makes the investment into the Aquaero very much worth it! What makes this type of set up so awesome is that the fans will only slowly ramp up and down with your coolant temperature. In the right red box you can see I added Ambient Top to the end of the label for the ambient sensor located on the top of one of the top radiators. Also there is a second ambient sensor located in front of the left front radiator. I actually save frequently to both Profile 1 and Profile 2. Profile 1 is my main everyday profile, I keep Profile 2 the same in case I want to try something a little different than what is on Profile 1, and I can do that without messing up Profile 1. When you activate this product you will receive the current version of the aquasuite software including an upgrade service for at least six (6) months. After the expiration of the upgrade service you may use and reinstall the latest version available during the upgrade period without a time limit.

I set my temperature range from .4° to 6°, and the power range from 13% to 100% Spend some time adjusting all of these numbers with your system at idle and under max load like RealBench until you get the fan speeds where you want them at both ends of the spectrum. My fans will never get down to 13%, but that got the rest of the curve where I wanted it. The curve starts out flat, but you can drag the slider to change how the curve ramps up and down. I closed the Temperature Sensors and Virtual Temperature Sensors sections so we can take a look at the reset of the Sensors pane. The next section is Software Temperature Sensors; here you can use either Aida 64 or HWiNFO monitoring programs to read any of the various sensors contained in those programs. I have both programs, but prefer HWiNFO for monitoring so that’s what I’m using. Alternatively to the LED strips offered by Aqua Computer, LED fans made by Corsair and NZXT can be connected using the optional accessory RGBpx Splitty4 (item code 53267, not included in delivery). Another warning states the slave unit will not be recognized by USB any longer and will only work over the Aquabus connected to the main Aquaero XT. Also keep in mind that the only outputs that will work on the slave unit are the four fan channels, the temp sensor inputs, and you can add a second flow meter to the Aquabus low port. All other outputs are now disabled.This way, even a broken pipe - and the pipes had diameters of 25mm - would not have been a problem. In the end, the project was realized without such a system, but the idea remained in my head. Such a system would have been too big and too expensive for our usual water cooling systems. So I started to develop concepts of such a system which are small and easy to integrate. Today's LEAKSHIELD is the result of a series of ideas and a puzzle that in the end became the finished product. The Aquaeros all come with four channels of fan control. Since I have two Aquaeros I have a total of eight fan channels. I have six radiators in total, 4 x 560, and 2 x 280 with a total of 30 140mm fans. I also have one 120mm fan in the HDD cage, and one 120mm fan in the rear of the case for exhaust. When you activate this product you will receive the current version of the aquasuite software including an upgrade service for at least eighteen (18) months. After the expiration of the upgrade service you may use and reinstall the latest version available during the upgrade period without a time limit. The Aquaero fan controllers are in my opinion the very best at controlling and monitoring your fans, pumps, and other accessories related to water or even air cooled PCs. The accompanying Aquasuite software is truly incredible and very powerful software! However, it can be a little intimidating if you have never used it before, and there is definitely a learning curve involved.

Power everything down again; you can disconnect the USB cable as it is unusable. Connect the Aquabus high port to a Hubby7 or the Aquabus high port on the Aquaero XT. Then you can connect your wiring for the extra fan channels to the Aquaero LT. You can actually add a third Aquaero for up to 12 channels of control if you need more channels.By constantly monitoring motor parameters and coolant temperature, a sophisticated algorithm is used by the controller unit to calculated the current coolant flow rate. The accuracy does not match the accuracy of an external flow sensor, but is entirely sufficient for monitoring purposes. Alternatively, a mechanical flow sensor can be connected to the fan output for a more accurate flow measurement. For the second Curve Controller I’m using my Software Sensor of the SSD temperature as the Data Source, notice how in this screen shot it shows 50°? That shows that my HWiNFO program was off when I took that screen shot. I named it SSD Fan Curve, and the Output is for Fan Channel 6 which only controls the 40mm fans in the SSD hot swap bay.