Simpson Strong Tie IS16-R100 16-Inch Insulation Support, 100-Pack

Product Information

Attach the garden netting to the roof rafters or studs: Using a staple gun, attach the end of a garden netting roll to the top of the furthest rafter and unroll it until you reach the next beam. Holding the garden netting taut, staple it to the second rafter. V., Şahin, S., Esteves, B., and Ayata, U. (2019). "Determination of thermal conductivity properties in some wood species obtained from Turkey ," BioRes . 14(3), 6709-6715. Available at: While the priority areas are predominantly located in northern and coastal regions, Which? also identified areas in the south of the UK such as Torridge and West Devon in Devon, St Ives in Cornwall, New Forest West in Dorset and North Norfolk in Norfolk - highlighting that this is a national issue. Davison, C., 2020. Specifying pipe supports - thermal performance. Kingspan. Available at: https://www.kingspan.com/gb/en-gb/products/technical-insulation/knowledge-base/articles-and-advice/specifying-pipe-supports-thermal-performance

Liam added that: 'A common mistake is cutting the insulation to fit between rafters or joists. It's much better installed as an independent layer without breaks in the insulation.' You can start with your first layer of insulation between the joists, but that second layer over the top will really improve its efficiency.Simply attach the nylon straps to the rafters in your attic using a staple gun or other attachment method. Staples, nails, screws, and hooks are all viable attachment options, so choose which one is best for your situation. To help mitigate this problem, you should install metal insulation supports sparingly and keep them near the outer edge of the wooden stud to allow as much room for the insulation as possible. Sheets, or boards, are made of natural or synthetic fibres and can be attached to the ceiling of your loft (the underside of your roof) and then decorated by painting or covering with plasterboard. You'll need to use this if you're intending to spend time in your loft or store temperature sensitive items in it, as heat from your home will rise up into your loft space to create a 'warm loft'.

You can decide not to go ahead if you do not agree with the assessment or costs. If you cannot use the online service One potential issue with using this type of attachment to hold up roof insulation is it can compress the material. You want to keep insulation as fluffy as possible, as compressing it can lower its R-value and cause it to be less efficient at insulating your home. Attach the insulation mesh to the wooden rafters or studs: Start on one side of the attic and attach the roll’s end to the wooden beam using a staple gun. Carefully unroll the mesh until you reach the next rafter and then staple it down, ensuring that the netting remains taut. Specifying pipe support systems can be complex, as such, our team of Technical Support Advisers provide a FREE project support service to our customers including consultation and problem-solving.

Head Office

Crawling around on your knees all day can get pretty gruelling, so you might benefit from using knee pads.

The majority of the constituencies which have the most need for insulation are in the North West and North East of England, Yorkshire and Humberside, the Welsh Valleys, South Scotland, West Belfast and Derry/Londonderry - but areas further south and London are also impacted. These are used along with pipe saddles/clamps to ensure that the pipe insulation does not compress at each support location. Start at the furthest point from the loft hatch and unroll the insulation over the top of the joists, ensuring an even, gap-free blanket over the entire space. Direct comparisons cannot be made between areas in different nations as not all the same data is available for each nation.

Enquiries

Attach the nylon straps to the studs or roof rafters: Once you’ve cut the straps to the correct length, use a staple gun or other attachment method to fasten the nylon straps to the roof rafters at 12-24 inch intervals. We have 100% quality control over all of our products since they are all manufactured within our own factories. Is it outdoors? If so, ensure it’s clad with suitable weatherproof material that matches the insulation specification. With energy prices having doubled over the last two years and the need to take action on climate change increasing exponentially, home energy efficiency has become a critical issue for households - yet current insulation levels fall worryingly short of where they need to be. If you have a flat roof, this also needs to be insulated by a professional, as the process is more complicated.