Joined in 2023 
82 
63 About this deal
Adjustable humidity setting between 40-90% RH, adjustable timer and momentary pull cord to override (HTM) A range of installable modules are available to allow customisation of activation options. Additional modules sold separately. Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pullcord, Timer, Humidity or Motion Sensing operation. Don’t forget to add the control module you want. Any module fits any fan. Its so iCON easy! Applications iCONsmart has been CB tested and FCC certified to demonstrate the thoughtful engineering behind the fan design. It has been awarded the TUV certification for its safety, functionality and quality. The Airflow ICON15 72683501 ventilation fan is suitable for fitting into walls or ceilings in areas such as shower rooms, bathrooms, en-suites and toilets.
The iCONsmart 15 is IPX5 rated and therefore it is suitable for mounting in bathrooms (in zone 1 and 2). The model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pullcord, Timer, Humidity or Motion Sensing operation. Don’t forget to add the control module you want. Any module fits any fan. Its so iCON easy! The icon 72683501 is mains voltage(240v) IPX4 rated and is suitable for installation into zone 3 of a bathroom or toilet. It may be flush mounted in either the wall or ceiling and with a low profile fascia, sits unobtrusively in any room. With an air extraction rate of 76m3 per hour, it easily surpasses building regulations. When the iCONsmart is first powered on, you will hear the initial reset for 10-15 seconds. This is normal and will also occur if the fan is in its reset mode. App Control and Setup
Frequently Asked Questions
Faced with an overwhelming choice of lens designs, materials and fitting techniques, today’s busy practitioners need a simple-to-fit, cost-effective RGP lens that delivers predictable results in the maximum number of patients, whether they’re new to RGP lens wear or accustomed wearers. Make provision for the electric supply cable and wall plugs / appropriate fittings using the main body as a template. Level using guides below the L and R symbols. (see Fig. 6) Airflow Developments Ltd shall not be liable for any loss, injury or other consequential damage, in the event of a failure of the equipment or arising from, or in connection with, the equipment excepting only that nothing in this condition shall be construed as to exclude or restrict liability for negligence. Full details at airflow.com/terms The iCON 15 is supplied for remote switching. Matching the required control functions (pull cord, timer, humidity, PIR, two speed) to the installation, simply means plugging in an interchangeable module into the iCON15 fan. Note: this fan is the basic version coming with remote switching; if you wish to add a timer module, a different face plate, or any other module, see the options below. iCON15 100mm Axial Ventilation Fan - Product Features
Do not use household cleaners containing abrasives. Cleaning of the internal parts such as the impeller should be carried out by using a soft brush. Never clean any parts of the fan assembly by immersing in water or using a dishwasher. SAFETY FIRST: ALWAYS ISOLATE THE FAN UNIT FROM THE POWER SUPPLY BEFORE DOING ANY WORK ON THE FAN / MODULE. The ICON15 comes complete with cantilever fixing lugs enabling a recessed installation on uneven surfaces. Do not place the fan near any direct heat sources, e.g. radiant heaters, or where the ambient temperature can exceed 40°C (104°F). For fans mounted in zones 1 & 2 as defined in BS 7671:2018, additional protection must be provided by a Residual Current Device (RCD) not exceeding 30mA as well as having an Arc Fault Detection Device (AFDD).iCON 15 Fan With Kit T is supplied with adjustable timer module, 140 x 140 x 100mm white square fixed grille, 100mm x 3m PVC flexible hose and cable ties iCONsmart has several features included as standard and can also be fitted with digital micro modules to give a range of extra control options. Standard Features Model above is for basic on/off switching. Choose an optional control module to upgrade fan for Pull cord, Pull cord with adjustable timer, Humidity, pull cord with timer overrun, motion sensor with timer overrun, Motion sensor/humidity/timer . Don’t forget to add the control module you want. Only low voltage module fits low voltage fans. It/s so iCON easy Applications: PRHTM - Infrared - Passive infrared activation with adjustable humidity setting and adjustable timer overrun. To replace the IPX cover, line up the L (Left) and R (Right) indicators on the main body of the fan (Fig. 6) with the L and R indicator on the IPX cover (Fig. 7). Lightly press the IPX cover onto the main body.
All electrical installation must be carried out by an approved electrician in accordance with Part "P" U.K. Building Regulations and to the latest IET standards, or the appropriate regulations in the country of installation. Fan and ducting should be inspected and cleaned on a regular basis to maintain fan performance. The external housing of the fan can be wiped with a damp cloth. Tiling is a breeze with the circular cover flange, reducing the need to 'make good' and one wipe and the cover is clean.Enter ICON – the new lens that provides a reassuringly simple and convenient solution to your RGP fitting needs. Easy to install due to the core drilled hole and its twist on/off cover enabling it to be fitted and fixed easily with its single side entry fixing screw. Ensure that flexible duct connections are not over tightened to the spigots. To maximise the air flow, rigid ducting should be used where possible. The fan and ducting should be installed in accordance with the requirements of the Domestic Ventilation Compliance Guide, part of Part F of the Building Regulations. Position the fan so cable entry and fitting holes align with those on the mounting surface. Feed through the cable and fit the fan. (Fig. 6) PRHTM - Infrared - Passive infrared activation with adjustable humidity setting and adjustable timer overrun
Great Deal 
New Comment